Dishwasher Not Cleaning Dishes? How to Tell What Actually Failed

Table of Contents
- 1. Start Here: Look at the Dish, Not the Dishwasher
- 2. Gritty Food Still Stuck On: Start With the Filter
- 3. Chalky White Film on Everything: That Is Our Water
- 4. The Part No National Guide Will Tell You: The Detergent Changed in 2010 and Our Water Did Not
- 5. Cloudy Glass: One Soak Tells You Whether It Comes Off
- 6. Greasy Dishes and an Undissolved Pod: The Water Is Not Hot Enough
- 7. When It Really Is the Dishwasher
- 8. What Each of These Costs in Livermore and the Tri-Valley
- 9. What to Do Yourself, and Where to Stop
- 10. Where We Work and What Else We Fix
- 11. Frequently Asked Questions
Your dishwasher runs a full cycle, you open the door, and the dishes are not clean.
Before you look at the dishwasher, look at the dishes. What is sitting on them tells you which of four completely different problems you have, and three of the four are not repairs at all.
Gritty bits of food still stuck on is one problem. A chalky white film over everything is a different problem with a different cause. Clear water spots are a third. Glass that has gone permanently cloudy is a fourth, and that one cannot be fixed by anyone.
Nearly every guide on this complaint hands you a single undifferentiated list of ten causes and leaves you to work out which one applies. That is how people end up buying a new dishwasher over a filter they did not know existed, or replacing a working pump when the real problem is that the water in this valley is hard, it gets harder every winter, and the detergent that used to handle it was reformulated in 2010.
Before you start: if you are going to take anything apart, switch the dishwasher off at the breaker first. Almost everything below needs no tools at all.
Start Here: Look at the Dish, Not the Dishwasher
Pull out a dish and a drinking glass from the last bad load and look at them in good light. Run a thumb across the surface.
| What you are seeing | What it usually is | Where to go |
|---|---|---|
| Gritty bits of food stuck on, often worse on the top rack | Filter, spray arms or loading | Gritty food, below |
| Chalky white film on dishes and on the tub walls | Hard water scale, and detergent that can no longer hold it | White film, below |
| Clear spots and streaks that wipe off with a towel | No rinse aid, or an empty dispenser | White film, below |
| Glass that stays cloudy no matter what you do | Etching, which is permanent | Cloudy glass, below |
| Greasy dishes, nothing dissolved, pod still sitting in the cup | Water not hot enough, or not enough water | Water temperature, below |
| Bottom rack clean, top rack dirty | Loading first, then the spray arm, feed tube or diverter | Gritty food, then dishwasher faults |
Then do these three free checks before anything else, because they take about five minutes between them and they settle most of these calls.
- Open the door four or five minutes into a cycle. There should be a couple of inches of water in the bottom and you should have heard it spraying. No water means a fill problem, which is a different article. Plenty of water and no spray sound points at the wash pump or a jammed spray arm.
- Spin both spray arms by hand with the racks out. They should turn freely with no scraping. Hold each one up to the light and check that the little holes are open rather than crusted shut.
- Pull the filter out of the floor of the tub and look at it. If you did not know your dishwasher had one, you have almost certainly found your problem, and we explain why in the next section.
Gritty Food Still Stuck On: Start With the Filter
This is the most common version of the complaint and the cheapest to fix, because it is usually not a fault at all.
Dishwashers come in two designs and most people have the second without knowing it. Older American machines used a hard food disposer, a small grinder that chopped debris up and sent it down the drain. Those were effectively self cleaning, and a generation of homeowners learned that a dishwasher looks after itself. Most units sold in the last fifteen years dropped the grinder in favour of a manual filter, because it is quieter and uses less water. That filter sits in the floor of the tub, usually under the lower spray arm, and it is yours to clean.
When it packs with debris, the machine recirculates dirty water over your dishes. That is why the symptom is food redepositing rather than food not coming off. Most manufacturers ask for it monthly. Almost nobody does it.
Taking it out is usually a quarter turn counter clockwise on the cylinder, then the flat mesh plate underneath lifts out. Rinse both under hot running water, work a soft brush over the mesh, and put them back. If you have never done it, do not be alarmed by what comes out.
The spray arms are the other half of this. Each arm has a row of small holes, and in this water they scale up and close down from the edges in. Take the arms off (they usually twist or unclip, or there is a single nut), push a toothpick through each hole, and rinse them out. If an arm wobbles, scrapes, or will not spin freely by hand, that is a worn bearing or a cracked hub rather than a cleaning job.
Three loading habits produce exactly this symptom as well, and they are worth ruling out before you spend anything:
- A tall item blocking a spray arm. A baking sheet or a cutting board in the wrong slot stops the arm turning, and everything downwind of it comes out dirty. This is the usual cause of a clean bottom rack and a dirty top rack.
- Overcrowding and nesting. Spoons stacked inside each other, bowls shielding the dishes behind them. Water cannot reach what it cannot see.
- Rinsing the dishes first. This one is counterintuitive. Modern machines have a soil sensor and the detergent enzymes need something to work on, so a load of pre rinsed dishes can trigger a shorter, gentler cycle. Scrape the large pieces off, leave the rest.
Chalky White Film on Everything: That Is Our Water
If the film is on the dishes, on the inside of the door and on the tub walls alike, and it comes off glass with a vinegar soak, you are not looking at a broken dishwasher. You are looking at dissolved minerals that got left behind when the water evaporated.
Livermore Municipal Water publishes the number. Water here typically carries 213 to 287 parts per million of calcium carbonate, which the City classifies as moderately hard to very hard. Livermore buys all of its treated water from Zone 7 Water Agency, and Zone 7 blends treated surface water from the Delta and Del Valle with local groundwater from Pleasanton.
And here is the part that explains why this complaint arrives in the winter. The blend is not constant through the year. The City states plainly that it draws more groundwater in the winter months, and that this raises hardness during that period. So a dishwasher that was acceptable in August genuinely does get worse in December, without anything mechanical having changed. If you have been told it is in your head, it is not.
Hard water hits a dishwasher in three places at once:
- On the dishes, as the chalky film and the cloudy glass.
- In the spray arm holes and the inlet valve screen, where scale narrows the openings and drops the wash pressure a little at a time, so the decline is slow enough that nobody notices a day it got worse.
- On the heating element, where a scale layer insulates the element from the water, so it takes longer to reach temperature and eventually fails early.
Water spots are the mild end of the same story and have a separate answer. Spots that wipe off with a towel are not a cleaning failure, they are drying marks, and they mean the rinse aid dispenser is empty or closed. Rinse aid is a surfactant: it breaks the surface tension so water sheets off the dish instead of beading and drying in place. In water this hard it is not an optional extra. Top it up roughly monthly and check that the dispenser cap actually clicks shut.
One more thing worth knowing if your dishes come out wetter than you remember. Many current machines, particularly the European designs common in newer Tri-Valley kitchens, dry by condensation against the stainless tub rather than with a heating element. They were designed around rinse aid being present. Run one dry and you get both spotting and wet dishes, and nothing is broken.
The Part No National Guide Will Tell You: The Detergent Changed in 2010 and Our Water Did Not
Here is where the published advice runs out, and it is the most useful thing on this page.
Every article on this problem tells you to clean the filter and consider a water softener. None of them tells you that the chemistry of dishwasher detergent was rewritten about fifteen years ago, that the ingredient that was removed was specifically the one that dealt with hard water, or that this is why a machine and a routine that worked fine for years quietly stopped working.
Dishwasher detergent used to contain phosphates. Phosphates are chelating agents: they bind up the calcium and magnesium in hard water so those minerals cannot interfere with the cleaning agents, and they hold food particles in suspension so the particles do not settle back onto the dishes while the water is being pumped around. Those two jobs are exactly the two failures people describe as a dishwasher not cleaning.
In July 2010 a group of US states banned phosphates in automatic dishwasher detergent, and rather than run separate batches, the manufacturers reformulated nationwide. Consumer Reports covered the switch as it happened and its testing found that none of the replacement formulations at the time matched the cleaning performance of the phosphate versions. The New York Times ran the same finding under the headline "Cleaner for the Environment, Not for the Dishes." The substitutes that went in, sodium citrate, polycarboxylates and similar, are decent chelators, but they are not as strong, and the gap shows up worst exactly where the water is hardest. GE Appliances still publishes a support page on white film appearing on glassware after the change.
The environmental reasoning was sound and we are not arguing with it. The practical consequence for a household on 213 to 287 ppm water is that the detergent is now doing a harder job with weaker tools, and you have to make up the difference yourself.
What actually makes up the difference, in the order we would try it:
- Fill the rinse aid and keep it filled. The single highest return action on this list, and it costs a few dollars a year.
- Use a pod or a fresh powder rather than an old box. Powder and gel absorb moisture over time and lose enzyme activity. A box that has lived under the sink since last year is weaker than it looks.
- Do not under dose. Dosing on the box assumes average water. On hard water, a fuller main wash cup is reasonable. Note that this runs the opposite way for glassware, which we come back to in the next section.
- Descale the machine every month or two. Run an empty hot cycle with a citric acid based dishwasher cleaner. A word of caution here, because most guides tell you to use white vinegar instead: several manufacturers advise against vinegar in a dishwasher, since the acid attacks rubber seals and gaskets over repeated use. A proper dishwasher cleaner does the same work without that argument.
- Check whether your machine has a built in water softener. Some dishwashers sold here, mainly European brands, have a softener and a salt reservoir built into the base of the tub, and an owner who has never filled it has been running on hard water the whole time. Look in your manual for "reactivation salt" or "water softener". The feature is not on every model sold in the US, so check before you buy salt.
And now the local point that contradicts the single most common piece of advice on this subject. Nearly every national article on dishwashers and hard water ends by telling you to install a water softener. In Livermore, the water utility asks you not to.
Livermore Municipal Water discourages salt regenerated water softeners, because the salt they discharge raises the salinity of the wastewater, which raises the salinity of the recycled water used for irrigation, which seeps back into the groundwater that the city then has to treat. Zone 7 runs a demineralization plant in Pleasanton to pull salt back out of that groundwater, and it is expensive. The City's own suggestion, if you decide you want softened water anyway, is a portable exchange tank service, where a company swaps the tanks on a schedule and disposes of the brine off site so it never reaches Livermore's wastewater at all.
That is a real decision with a local answer, and you will not find it on a national site.
Cloudy Glass: One Soak Tells You Whether It Comes Off
Glassware that has gone permanently foggy is its own problem, and it is worth separating from the film above because one of them is fixable and the other is not.
The test takes five minutes and costs nothing. Put the cloudy glass in a bowl of plain white vinegar, or hold a vinegar soaked paper towel against it, for about five minutes, then rinse and dry.
- The cloudiness lifts and the glass is clear again. That is mineral film sitting on the surface. It is the hard water problem above, and everything in the previous two sections applies.
- The cloudiness is still there. That is etching. The glass surface itself has been corroded and there is nothing anyone can do to restore it. New glasses will go the same way if the conditions that caused it stay the same.
Etching is driven by a combination of soft or softened water, too much detergent, and high water temperature over many cycles. That is worth holding alongside the previous section, because it is the one direction where more detergent and a water softener will make things worse rather than better. If you have had a softener fitted and your glasses have since gone permanently cloudy, those two facts are related.
What to change if you are getting etching: cut the detergent dose back, use the lower temperature or eco cycle for glassware, and wash delicate or thin glass by hand. If your water is genuinely softened, a smaller dose will still clean, because the detergent is no longer fighting the minerals.
This is also the one case where the honest answer is that we cannot help. If a technician offers to fix etched glassware, something is wrong.
Greasy Dishes and an Undissolved Pod: The Water Is Not Hot Enough
A distinct signature: nothing has dissolved, there is grease left on everything, and the detergent pod is still sitting in its cup looking almost untouched, or there is a crust of powder in the bottom of the tub.
Detergent enzymes and the surfactants that cut grease both need heat to work. Below roughly 120 degrees the detergent never fully dissolves and never fully activates, and the cycle finishes having mostly rinsed the dishes in warm water.
Three things cause it, in the order we find them:
- The water arriving is not hot enough. Dishwashers are plumbed to the hot supply, and most manufacturers want water reaching the machine at about 120 degrees. If the water heater is set low, or the kitchen is a long run from it, the first fill is the one that suffers most. Run the kitchen tap hot for thirty seconds before you start the machine. It is free, it works, and it is the fix in a surprising number of these calls.
- The heating element is not boosting. Most machines heat the water further during the wash. HomeGuide notes that elements have to reach 150 degrees to meet NSF sanitizing standards. A scaled or failed element leaves the cycle running on whatever the house supplied, which in winter in this valley is not much. If you also have dishes coming out soaked at the end of a heated dry cycle, that points the same way.
- The pod is going in the wrong place. A pod dropped loose in the bottom of the tub dissolves during the pre rinse and is gone by the time the main wash starts. It belongs in the closed dispenser cup, which opens partway through the cycle for exactly this reason. Check too that nothing on the bottom rack is blocking the cup from springing open.
When It Really Is the Dishwasher
If the filter is clean, the spray arms turn freely with open holes, the rinse aid is full and the water is hot, then something has failed. These are the ones we actually get called out for.
- The wash pump or its motor. The pump that drives the spray arms. When it weakens, wash pressure drops and the dishes come out progressively worse over a few months rather than suddenly. The tell is a cycle that sounds quieter than it used to, or a hum with no real spray noise behind it.
- The diverter valve. On machines with upper and lower arms, a diverter alternates pressure between them. When it sticks, one rack gets everything and the other gets nothing, for the whole cycle. This is the fault behind a clean bottom rack and a dirty top rack when the arm itself is fine and nothing is blocking it.
- A cracked or blocked upper feed tube. The pipe that carries water up the back wall to the top arm. A crack dumps the pressure into the tub halfway up. Same symptom, different part.
- The chopper or macerator, on machines that have one. When the blade dulls or jams, larger debris is no longer broken down, and it ends up back on the dishes and packed into the filter faster than you can clean it.
- A scaled inlet valve screen. The valve has a fine screen on the supply side, and in this water it scales up. The machine then fills short, so there is not enough water to wash with. Often this is a clean rather than a replacement.
- The heating element. As above, a failed element gives you cold water washing and wet dishes at the end.
- The control board. Real, and the most expensive thing on the list, but much rarer than the internet suggests. Everything above gets checked first.
The theme worth noticing is that three of those seven are caused or accelerated by hard water. That is not a coincidence, and it is why the descaling in the earlier section is maintenance rather than cosmetics. The same mineral load is behind a refrigerator leaking water from a scaled fill tube and behind the inlet valves we replace in washing machines.
What Each of These Costs in Livermore and the Tri-Valley
The national figures below come from HomeGuide's dishwasher repair cost data, which puts a typical dishwasher repair at $100 to $300 nationally with a minimum service fee of $70 to $130. The right hand column adjusts for Bay Area labor, which runs well above the national average, and it is where our own quotes usually land.
| Repair | National range | Tri-Valley range |
|---|---|---|
| Cleaning the filter, spray arms and rinse aid | free | free |
| Descaling the machine | free | free |
| Water inlet valve | $80-$170 | $100-$215 |
| Spray arm | $80-$200 | $100-$250 |
| Drain hose | $80-$180 | $100-$225 |
| Door gasket or seal | $80-$200 | $100-$250 |
| Door spring and latch | $90-$160 | $115-$200 |
| Float switch | $90-$190 | $115-$240 |
| Filter assembly | $90-$175 | $115-$220 |
| Drain pump | $100-$400 | $125-$500 |
| Heating element | $200-$350 | $250-$440 |
| Control board | $200-$600 | $250-$750 |
| Wash motor or pump assembly | $350-$500 | $440-$625 |
| Diagnostic visit | $70-$130 | $80-$165 |
A few things worth drawing out of that table.
The most common answer on this page is the free one. If the fault is the filter, the spray arm holes, the rinse aid or the water temperature, you are looking at nothing but twenty minutes and a bottle of rinse aid. We would rather you fixed those without us.
The 50 percent test still applies. HomeGuide puts a replacement dishwasher at $600 to $1,700 installed, with the unit alone at $400 to $1,200, and life expectancy at 8 to 15 years. If the quote comes back above half the cost of a comparable replacement on a machine already past ten years, replacement is usually the better decision. For everything on that table except a wash motor or a control board on an old unit, that rarely happens. We go through the full picture in our guide to what appliance repair costs in Livermore and the Tri-Valley.
Watch out for the cheap part that is really a symptom. A heating element or an inlet valve that failed because of scale will fail again if nothing changes about the descaling routine. We will tell you that when we quote it.
What to Do Yourself, and Where to Stop
Most of this list is not a repair and we are happy to say so.
Worth doing yourself:
- Look at the dish and decide which of the four symptoms you have before anything else.
- Pull out and wash the filter, then put it on a monthly schedule.
- Clear the spray arm holes with a toothpick and check both arms spin freely.
- Fill the rinse aid and make sure the dispenser cap is properly closed.
- Run the kitchen tap hot for thirty seconds before starting a cycle.
- Descale the machine every month or two with a citric acid dishwasher cleaner.
- Stop pre rinsing, scrape instead, and give the spray arms room to turn.
- Do the vinegar soak on one cloudy glass to find out whether it is film or etching.
- Check your manual for a built in water softener and salt reservoir if you own a European brand machine.
Worth calling about:
- Wash pressure that has faded over months with a clean filter and clear spray arms, which usually means the wash pump
- One rack clean and the other dirty with nothing blocking either arm, which usually means the diverter or the upper feed tube
- A spray arm that scrapes, wobbles or will not turn by hand
- Cold water washing that survives a hot tap run and a descale, which means the heating element and a meter
- A machine that fills short, which can be the inlet valve screen, the valve itself or the float switch
- Anything involving removing the dishwasher from under the counter, because the supply line, the drain line and the electrical connection all come with it and a flooded kitchen cabinet costs far more than the repair did
Dr. Appliance has been repairing dishwashers across Livermore and the Tri-Valley for over 20 years. We are licensed and insured, we carry spray arms, inlet valves, pumps, elements and door gaskets on the vans, and most of these jobs finish on the first visit.
Call (925) 667-3597 and tell us three things: what is actually on the dishes, whether the filter has been cleaned recently, and whether the water in your kitchen tap runs properly hot. Those three answers usually tell us what to bring.
Where We Work and What Else We Fix
We handle dishwasher repair for built in, drawer and portable units, across the mainstream brands and the built in European ones, and we see the hard water failures in this valley often enough to know where to look first. We also cover refrigerator and freezer repair, washer and dryer repair, oven, stove and range repair and microwave repair. Browse all of our services, read more about our residential appliance repair, or see what we do across appliance repair in Livermore and appliance repair in Dublin. We also provide commercial appliance repair services for restaurants, hotels, laundromats and property managers throughout the Tri-Valley.
Our service area covers Livermore, Pleasanton, Dublin, San Ramon, Danville, Tracy, Castro Valley, Fremont, Walnut Creek and the surrounding East Bay. You can also reach us through our Contact us page.
If the same water is giving you trouble elsewhere in the house, our guide to a washing machine that will not drain covers the inlet valves and pumps on the laundry side, and the one on a refrigerator leaking water covers the fill tube and valve that scale up behind the fridge.
Frequently Asked Questions
Ready to Schedule a Repair?
Dr. Appliance provides fast, professional appliance repair for homes and businesses throughout Livermore and the Tri-Valley.


